Friday, February 25, 2011

and now, number 7!!!




Hi everyone,
It has been a busy couple of weeks....after I got back from Carol's I had to get ready for my two day class with Jeff Devers. We were going to making boxes with lids....Jeff does some of the most amazing boxes out of polymer clay. We started by making a box out of card stock and then covering them with clay and baked them. We used these as our interior molds. We built up our boxes in layers with a lot of baking and sanding in between (good thing we had a day off to catch up on our "homework"). We then learned how to make two different kinds of fitted lids. It was interesting to see how Jeff works and how he pays so much attention to detail. I would show you a photo of mine but I loaned it to my gal, Gloria, so she could work on her next step.....when I get it back I will put on a decorative layer, bake and sand again...then I will post a photo of the finished piece! Something to look forward to!
In between getting ready for the workshop and the couple of days after, I have been busy in the studio when I haven't been in bed with the flu. I finished off 4 rings that I had in various stages of being finished, and 1 completely new one, so now I am not behind on my RAW!! So, I will start with the new one.....really simple...I had a wonderful piece of copper metal clay that I had textured in Gordon's class with the tearaway method last Feb. I antiqued the surface with acrylic paint and then heat set it before sanding the surface lightly with sandpaper to bring out the details of the little angel. I also had some little bits of already fired metal clay and one of them was a #7 and was just the right size to use on the surface, so I antiqued that with the same colors of acrylic paint. If you look closely, you will see that the little angel looks like he is holding the big ball with one hand and throwing a little ball up in the air with his other hand. The little ball is actually the rivet that holds part of the ring together. Since I don't solder, I needed to figure out how to attach the shank to the band. I decided to use the holes in the #7 disc and the upper right hand corner, which worked out to look like he was tossing a ball in to the air. I liked the way a bit of the band peeked out of the far edge and decided to keep it and then added a little amethyst stone to the sterling band. The little tab also holds the ring in place and keeps it from spinning. It is quite comfortable to wear even though it is off center.
So, for ring number 8, I had a ring cut out from a Faux Bone blank and had experimented with coloring the surface last summer. It has been sitting on my worktable just waiting for the right little something. When I had found my little number 7 disc, I had also found some of the long fragments that I used to make for earrings. I also had a large disc...I hammered that into a bowl so I could set one of those rivoli stones into it and I had a purple one that worked with the surface of the already dyed faux bone ring, so I started assembling the ring. I used two long fragments on the sides and used some sterling headpins to attach everything together. I then found a smaller fragment that fit in between the two that worked out well. When those were attached, I drilled a hole in the faux bone with a round tip bur and set the bowl into it after doming the center section in a smaller divot to conform the bottom of the bowl. I then set the rivoli in and chemically bonded the whole thing together. Yes, I know, it is the easy way out, but have you ever tried to rivet on a ring band? It is hard to flip the ring and hammer on the inside of the band....and since I had to use epoxy to glue the rivoli into the bowl, I really didn't mind.
So, while all the epoxy was drying, I pulled out some rings I had made in a class with Tim McCrieght. I liked the idea of the rings but they were too big, even for me, so I thought about what I could do to shrink the interiors so they would fit. I had made a polymer sheet that looked like slabs of wood and it ended up being the right thickness to close up the interior so the rings fit nicely. I love the natural patina on the two rings. The third was in a plastic bag, so no patina as of now. I am still playing with the idea of setting some small white topaz in a couple of the rings. Well, that is all for now...hope you like some of the rings....let me know if you can...I would love to hear from you...have fun in your studios....Kelly

4 comments:

  1. Wow Kelly!
    I love the Angel...looks like you've been busy! AND you've been having the flu?! I didn't know you were sick...well I'm glad you're feeling better!
    Seeing your rings inspires one to think outside the "circle" - Thanks for all the details.
    Love,
    Terresa

    ReplyDelete
  2. Thanks, Honey! I had a great time in the studio....I am feeling better. And thinking outside the "circle"??? you may have to call to explain that one!! Love, K

    ReplyDelete
  3. Thanks Sophia....I am really glad to know that someone is enjoying my crazy thoughts about creating! Hope you, too, are having fun in your studio. Best, Kelly

    ReplyDelete
  4. Sophia....I just went to your website and all I can say is WOW!!!! I LOVE all of your pieces....just fab!!! I have a thing for dots and granulation....although, that could be because I have dots all over me....freckles.....thanks again for your compliments, Kelly

    ReplyDelete